詳解Linux下掛載新硬盤方法
Linux的硬盤識別:
一般使用”fdisk -l”命令可以列出系統中當前連接的硬盤
設備和分區信息.新硬盤沒有分區信息,則只顯示硬盤大小信息.
1.關閉服務器加上新硬盤
2.啟動服務器,以root用戶登錄
3.查看硬盤信息
#fdisk -l
Disk /dev/sda: 42.9 GB, 42949672960 bytes 255 heads, 63 sectors/track, 5221 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004406e Device Boot Start End Blocks Id System /dev/sda1 * 1 39 307200 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 39 2589 20480000 83 Linux /dev/sda3 2589 2850 2097152 82 Linux swap / Solaris /dev/sda4 2850 5222 19057664 5 Extended /dev/sda5 2850 5222 19056640 83 Linux Disk /dev/sdb: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14b52796 Device Boot Start End Blocks Id System
4.創建新硬盤分區命令參數:
fdisk可以用m命令來看fdisk命令的內部命令;
- a:命令指定啟動分區;
- d:命令刪除一個存在的分區;
- l:命令顯示分區ID號的列表;
- m:查看fdisk命令幫助;
- n:命令創建一個新分區;
- p:命令顯示分區列表;
- t:命令修改分區的類型ID號;
- w:命令是將對分區表的修改存盤讓它發生作用。
5.進入磁盤,對磁盤進行分區,注意紅色部分。
#fdisk /dev/sdb
Command (m for help):n Command action e extended //輸入e為創建擴展分區 p primary partition (1-4) //輸入p為創建邏輯分區 p Partion number(1-4):1 //在這里輸入l,就進入劃分邏輯分區階段了; First cylinder (51-125, default 51): //注:這個就是分區的Start 值;這里最好直接按回車,如果您輸入了一個非默認的數字,會造成空間浪費; Using default value 51 Last cylinder or +size or +sizeM or +sizeK (51-125, default 125): +200M 注:這個是定義分區大小的,+200M 就是大小為200M ;當然您也可以根據p提示的單位cylinder的大小來算,然后來指定 End的數值?;仡^看看是怎么算的;還是用+200M這個辦法來添加,這樣能直觀一點。如果您想添加一個10G左右大小的分區,請輸入 +10000M ; Command (m for help): w //最后輸入w回車保存。
查看一下:
#fdisk -l
可以看到/dev/sdb1分區,我就省略截圖咯。
6.格式化分區:
#mkfs.ext3 /dev/sdb1 //注:將/dev/sdb1格式化為ext3類型
mke2fs 1.41.12 (17-May-2010) 文件系統標簽= 操作系統:Linux 塊大小=4096 (log=2) 分塊大小=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 640848 inodes, 2562359 blocks 128117 blocks (5.00%) reserved for the super user 第一個數據塊=0 Maximum filesystem blocks=2625634304 79 block groups 32768 blocks per group, 32768 fragments per group 8112 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632 正在寫入inode表: 完成 Creating journal (32768 blocks): 完成 Writing superblocks and filesystem accounting information: 完成 This filesystem will be automatically checked every 35 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override.
這樣就格式化好了,我們就可以用mount 加載這個分區,然后使用這個文件系統;
7.創建/data1目錄:
#mkdir /data1
8.開始掛載分區:
#mount /dev/sdb1 /data1
9.查看硬盤大小以及掛載分區:
#df -h
10.配置開機自動掛載
因?yàn)閙ount掛載在重啟服務器后會失效,所以需要將分區信息寫到/etc/fstab文件中讓它永久掛載:
#vim /etc/fstab
加入:
/dev/sdb1(磁盤分區) /data1(掛載目錄) ext3(文件格式)defaults 0 0
11.重啟系統
以上就是本文的全部內容,希望對大家的學習有所幫助,也希望大家多多支持本站。
版權聲明:本站文章來源標注為YINGSOO的內容版權均為本站所有,歡迎引用、轉載,請保持原文完整并注明來源及原文鏈接。禁止復制或仿造本網站,禁止在非www.sddonglingsh.com所屬的服務器上建立鏡像,否則將依法追究法律責任。本站部分內容來源于網友推薦、互聯網收集整理而來,僅供學習參考,不代表本站立場,如有內容涉嫌侵權,請聯系alex-e#qq.com處理。