linux下使用Apache搭建文件服務器的步驟
發布日期：2021-12-30 19:47 | 文章來源：源碼之家
一.關于文件服務器
在一個項目中，如果想把公共軟件或者資料共享給項目組成員，可以搭建一個簡易的文件服務器來實現，只要是在局域網內的成員都可以通過瀏覽器或者wget命令來下載和訪問資料。可以達到信息共享，軟件版本一致的效果。本文講述在linux環境下使用Apache服務搭建文件服務器。
二.使用Apache搭建文件服務器
1.Apache服務在linux環境下的程序叫做httpd，所以首先安裝httpd服務，如果配置好了yum源的話，直接使用yum命令安
裝,如果沒有配置好yum源的話，可以參考博客“l(fā)inux 配置本地yum源，配置國內yum源，配置epel源”進行配置，網址為：//www.jb51.net/article/202406.htm
[root@node5 ~]# yum -y install httpd
2.啟動httpd服務
#啟動httpd服務
[root@node5 ~]# systemctl start httpd
#查看httpd服務狀態
[root@node5 ~]# systemctl status httpd
● httpd.service - The Apache HTTP Server
Loaded: loaded (/usr/lib/systemd/system/httpd.service; disabled; vendor preset: disabled)
Active: active (running) since Thu 2020-12-17 16:26:05 CST; 7s ago
Docs: man:httpd(8)
man:apachectl(8)
Main PID: 98576 (httpd)
Status: "Processing requests..."
CGroup: /system.slice/httpd.service
├─98576 /usr/sbin/httpd -DFOREGROUND
├─98577 /usr/sbin/httpd -DFOREGROUND
├─98578 /usr/sbin/httpd -DFOREGROUND
├─98579 /usr/sbin/httpd -DFOREGROUND
├─98580 /usr/sbin/httpd -DFOREGROUND
└─98581 /usr/sbin/httpd -DFOREGROUND
Dec 17 16:26:05 node5 systemd[1]: Starting The Apache HTTP Server...
Dec 17 16:26:05 node5 httpd[98576]: AH00558: httpd: Could not reliably determine the server's fully qualified domain name, using 192.168.110.184. Set the 'ServerName' directive globally to su...ss this message
Dec 17 16:26:05 node5 systemd[1]: Started The Apache HTTP Server.
Hint: Some lines were ellipsized, use -l to show in full.
#查看Apache版本
[root@node5 ~]# httpd -version
Server version: Apache/2.4.6 (CentOS)
Server built: Nov 16 2020 16:18:20
3.查看IP地址，訪問Apache頁面
#可以看到本機IP地址為192.168.110.184
[root@node5 soft]# ifconfig
ens33: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.110.184 netmask 255.255.255.0 broadcast 192.168.110.255
ether 00:0c:29:11:c4:4a txqueuelen 1000 (Ethernet)
RX packets 24682 bytes 13301526 (12.6 MiB)
RX errors 0 dropped 4 overruns 0 frame 0
TX packets 15119 bytes 2166095 (2.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 2402 bytes 221903 (216.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2402 bytes 221903 (216.7 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
在瀏覽器里訪問http://192.168.110.184/，如果出現如下界面說明Apache服務安裝成功
4.創建共享目錄/opt/soft，把需要共享的文件都放在這個目錄
[root@node5 soft]# mkdir /opt/soft
#此命令把系統所有的tar.gz的壓縮包都放在共享目錄里
[root@node5 soft]# find / -name "*.tar.gz" -exec mv {} /opt/soft \;
[root@node5 soft]# ls /opt/soft/
amhello-1.0.tar.gz elasticsearch-6.2.2.tar.gz FastDFS_v5.08.tar.gz kibana-6.2.2-linux-x86_64.tar.gz nginx-1.19.3.tar.gz ntp-4.2.6p5.tar.gz tomcat-native.tar.gz
apache-tomcat-8.0.51.tar.gz fastdfs_client_java._v1.25.tar.gz findfile.tar.gz libopts-40.0.15.tar.gz nginx-1.8.0.tar.gz rarlinux-3.8.0.tar.gz 餅干.txt
commons-daemon-native.tar.gz fastdfs-nginx-module_v1.16.tar.gz jdk-8u172-linux-x64.tar.gz nginx-1.10.0.tar.gz ngx_cache_purge-2.3.tar.gz today_db.tar.gz
5.因為訪問Apache頁面默認讀取的是/var/www/html/頁面，所以把共享目錄鏈接到/var/www/html/下就可以了
[root@node5 ~]# ln -s /opt/soft /var/www/html/file [root@node5 ~]# ll /var/www/html/file lrwxrwxrwx 1 root root 9 Dec 17 16:29 /var/www/html/file -> /opt/soft
6.重啟Apache服務，查看頁面
[root@node5 ~]# systemctl restart httpd
使用瀏覽器訪問http://192.168.110.184/file/，如果出現如下界面，就說明文件服務器搭建好了
7.通過網頁我們發現中文是亂碼，可以修改配置文件使中文正常顯示
#在Apache配置文件的末尾追加一行 [root@node5 ~]# echo "IndexOptions Charset=UTF-8" >> /etc/httpd/conf/httpd.conf [root@node5 ~]# systemctl restart httpd
再次訪問網頁http://192.168.110.184/file/，發現頁面的中文正常顯示了
三.測試文件服務器是否可用
1.在windows上使用瀏覽器訪問http://192.168.110.184/file/，如果頁面可以打開，并且點擊軟件會自動下載，說明通過windows下載文件成功。
2.在局域網內的另外一臺linux機器上測試是否可以下載文件
#首先在node8機器上使用root賬戶測試下載文件 #使用wget命令下載文件 [root@node8 ~]# wget http://192.168.110.184/file/餅干.txt --2020-12-17 16:53:00-- http://192.168.110.184/file/%E9%A5%BC%E5%B9%B2.txt Connecting to 192.168.110.184:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181 (1.2K) [text/plain] Saving to: ‘餅干.txt' 100%[=======================================================================================================================================================================>] 1,181 --.-K/s in 0s 2020-12-17 16:53:00 (130 MB/s) - ‘餅干.txt' saved [1181/1181] [root@node8 ~]# wget http://192.168.110.184/file/today_db.tar.gz --2020-12-17 16:53:26-- http://192.168.110.184/file/today_db.tar.gz Connecting to 192.168.110.184:80... connected. HTTP request sent, awaiting response... 200 OK Length: 767 [application/x-gzip] Saving to: ‘today_db.tar.gz' 100%[=======================================================================================================================================================================>] 767 --.-K/s in 0s 2020-12-17 16:53:26 (268 MB/s) - ‘today_db.tar.gz' saved [767/767] #發現文件能正常下載 [root@node8 ~]# ls 餅干.txt today_db.tar.gz today_db.tar.gz 餅干.txt #使用node8機器上的普通賬戶file1測試下載文件 [root@node8 ~]# useradd file1 [root@node8 ~]# echo "123456" | passwd --stdin file1 Changing password for user file1. passwd: all authentication tokens updated successfully. [root@node8 ~]# su - file1 [file1@node8 ~]$ pwd /home/file1 [file1@node8 ~]$ ls [file1@node8 ~]$ wget http://192.168.110.184/file/餅干.txt --2020-12-17 17:44:10-- http://192.168.110.184/file/%E9%A5%BC%E5%B9%B2.txt Connecting to 192.168.110.184:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181 (1.2K) [text/plain] Saving to: ‘餅干.txt' 100%[=======================================================================================================================================================================>] 1,181 --.-K/s in 0s 2020-12-17 17:44:10 (254 MB/s) - ‘餅干.txt' saved [1181/1181] [file1@node8 ~]$ wget http://192.168.110.184/file/today_db.tar.gz --2020-12-17 17:44:20-- http://192.168.110.184/file/today_db.tar.gz Connecting to 192.168.110.184:80... connected. HTTP request sent, awaiting response... 200 OK Length: 767 [application/x-gzip] Saving to: ‘today_db.tar.gz' 100%[=======================================================================================================================================================================>] 767 --.-K/s in 0s 2020-12-17 17:44:20 (216 MB/s) - ‘today_db.tar.gz' saved [767/767] #發現能正常下載文件 [file1@node8 ~]$ ls today_db.tar.gz 餅干.txt
自此文件服務器搭建成功，功能正常。
以上就是linux下使用Apache搭建文件服務器的步驟的詳細內容，更多關于Linux 搭建文件服務器的資料請關注本站其它相關文章！
版權聲明：本站文章來源標注為YINGSOO的內容版權均為本站所有，歡迎引用、轉載，請保持原文完整并注明來源及原文鏈接。禁止復制或仿造本網站，禁止在非www.sddonglingsh.com所屬的服務器上建立鏡像，否則將依法追究法律責任。本站部分內容來源于網友推薦、互聯網收集整理而來，僅供學習參考，不代表本站立場，如有內容涉嫌侵權，請聯系alex-e#qq.com處理。
相關文章
關注官方微信